Air Conditioning & MMI Rotary Knobs/Buttons Replacement Kit for Audi Q7 I (2005–2010)

One Kit, Every Button — Audi Q7 4L AC & MMI Controls Restored

The Audi Q7 4L puts a lot of buttons between you and your comfort. Climate zones, seat heating, MMI navigation, media controls — you reach for them dozens of times every drive. After a decade of daily use, those surfaces show it: rubber peeling off the MMI knob, AC buttons sticky or completely bare, labels worn to nothing. This Air Conditioning & MMI Buttons Knobs Replacement Kit for Audi Q7 I 4L (2005–2015) restores both systems in one go — no partial fixes, no mismatched finishes.

What's in the Kit

The Q7 4L Button Problem — And Why It Gets Worse

Audi's first-generation Q7 uses a soft-touch rubber coating on virtually every button surface. It feels premium when new — and becomes a problem within a few years. Heat from the sun, oils from your hands, and everyday cleaning products all break down the coating. The MMI buttons tend to go first because they're used constantly for navigation and media. The AC controls follow, especially around the fan speed and temperature knobs. By 100,000 km, most Q7 4L owners are looking at buttons that feel nothing like the car they bought. This kit addresses both failure points with durable ABS that holds up where the factory rubber didn't.

AC Controls + MMI Together — Why It Matters

Most replacement kits target one system. The problem: your eye catches the contrast immediately. A fresh MMI knob next to worn AC buttons — or vice versa — looks worse than leaving everything as-is. This kit covers both the climate control panel and the MMI interface, so the entire center of your Q7's interior matches. One purchase, one restoration, consistent result.

Confirmed Fitment for the Full Q7 4L Run

• Audi Q7 4L — all engine variants (3.0 TDI, 3.6 FSI, 4.2 FSI, 4.2 TDI, 6.0 TDI W12)
• Model years 2005 through 2015
• Compatible with pre-facelift (2005–2009) and facelift (2010–2015) — same MMI layout
• Includes SQ7 early production where applicable

Not sure which MMI generation your Q7 has? If your center console has a round rotary dial with 4–8 surrounding push buttons and your climate panel sits above it on the dashboard, this kit fits.

Tool-Free Installation in Under 10 Minutes

No workshop, no wiring, no disassembly. Each button and knob in this kit is a direct clip-on replacement for the original. Remove the worn pieces by hand — they pull straight off — and press the new ones in. The fit is firm and precise, with the same tactile click as factory. Fully reversible, no permanent modification to your vehicle.

Go Further With Your Q7 Interior Restoration

If your MMI and AC buttons are worn, your window switches and steering wheel controls likely aren't far behind. Browse our full Audi interior restoration range to refresh every touch point in one order. We also carry Audi Q5, A4 B8, and A5 replacement button kits if you're maintaining multiple vehicles.

Frequently Asked Questions

Does this cover the MMI 2G or MMI 3G system?

The Q7 4L launched with MMI 2G and was updated to MMI 3G during the 2010 facelift. Both systems use the same physical button and knob format — this kit is compatible with both generations.

Will these buttons match my current interior?

Yes. The kit is finished in the standard Audi Q7 4L black used across all trim levels. The gloss and texture are matched to the factory spec, so the replaced pieces blend seamlessly with surrounding panels.

My MMI knob wobbles but still turns — is it worth replacing?

If the wobble is in the cap (the outer knob piece), yes — this kit resolves it. The replacement knob clips firmly onto the underlying shaft and eliminates the play. If the shaft itself is loose, that's an internal MMI unit issue separate from this kit.

Is any adhesive required?

No. Everything clips on mechanically. No glue, no tape, no risk of residue on your panels.

Can I replace just the MMI buttons without the AC buttons?

The kit is sold as a complete set. We recommend replacing both at the same time — the finish match is exact, and the labour difference between replacing one system versus both is zero.